AETA AUDIO
MIX2000 PORTABLE STEREO FIELD MIXER
(WITH M-S AND OPTIONAL DIGITAL OUTPUT)
The Mix2000 is arguably the most rugged and feature-packed portable field mixer on the market. Weighing less than 5 lbs and not much bigger than a paperback book, the Mix2000 provides everything from M-S Decoder to selectable PPM or VU metering. For the ultimate in audio performance, durability, and features, the Mix2000 is "simply the best!"
Mix2000 Portable Stereo Field Mixer (with M-S)
FEATURES:
- Four symmetrical transformer balanced inputs
- Ultra-low noise (-130 dB)
- Outstanding input headroom (46 dB)
- AES/EBU or S/PDIF optional output module
- Independant M-S decoders for outputs and monitors
- High sensitivity VU or peak LED metering
- VCA controlled master stage with selectable compressor and limiter
- Microphone powering: PH 48V, PH 12V, or T-12V
- High performance monitoring source and listening mode selection
- Small weight and size (<5 lbs including batteries)
.APPLICATIONS:
- Film and Video Location
- Recording
- News Gathering
- Sound Effects Capture
- Remote Broadcast
- Scientific Work
TECHNICAL FEATURES:
Mic Input Impedance: >2 kOhms (20 Hz to 20 kHz) Input Transformer Gain: +15.6 dB (N+1/6) Input Transformer Insulation: 500 VDC Maximum Total Gain: >90 dB per channel Input Stage Gain Range: Max = 42 dB, Min = 0 dB Nominal Input Stage Headroom 46 dB Pad Nominal Attenuation: -26 dB Line Input Impedance: 10 kOhms, typical (with pad "ON") Max. Input Level with pad "ON"
+27 dBu Microphone Powering: 3-position switches: Phantom, Off, T-12 Bandwidth: 20 Hz to 20 kHz @ +/- 0.15 dB, (10Hz @ better than -1 dB) Noise Referred to Input: -130 dBu (Bandwidth: 20 Hz-20 kHz, unweighted) T.H.D. + Noise: >0.1%, 20 Hz to 20 kHz, for any total gain <50 dB Crosstalk between inputs: >80 dB, from 20 Hz-20 kHz Common Mode Rejection: better than 65 dB, typically 80 dB, from 20 Hz-20 kHz Electronically Balanced Output Stage Ouput Impedance : 50 Ohms; >+20 dBu Emax (>7 Vrms / 600 Ohms) Output headroom: +16 dB relative to 0 VU = +4 dBm Sub Outputs: Asymmetrical, output impedance; 50 Ohms, +20 dBu Emax (>7 Vrms / 600 Ohms) Extension Output: (Sub-D, 9 pins, female) Direct Channel Outputs: 4 x asymmetrical, output impedance; 100 Ohms, +20 dBu Emax (>7 Vrms / 600 Ohms) Main Channel Outputs: 2 x asymmetrical, output impedance; 100 ohms, +20 dBu Emax (>7 Vrms / 600 Ohms) Headphone Output: 1/4 inch, stereo, output impedance; 50 ohms, +20 dBu Emax (>7 Vrms / 600 Ohms), fully short-circuit protected Wireless receiver output with power supply on a 6-pin Hirose connector AES/EBU or S/PDIF (Optional): Plug-In module, output via UHF Hirose 6-pin connector; sample frequencies 44.1 or 48 kHz; resolution 24 Bits Input Stage Sensitivity Adjustment: 8 steps (7 x 6 dB = 42 dB) rotary switch with knob Input -26 dB PAD insertion switch Microphone powering switch 3-position, Phantom, Off, T-12 Overload red LED indication @ -6 dB before input stage saturation (full wave detection) Polarity inversion switch, with green LED indicator for phase-inverted signal 3-position switch for High-Pass Filter: "OFF" 80 Hz and 120 Hz (-12 dB/octave) Dual potentiometer: internal knob = channel level, outer ring = pan-pot Stereo coupling switches (1+2 and 3+4) Dual shaft potentiometer for Master Gain and Balance D.C. noiseless controlled gains (common voltage command for the two channels) L/R controlled gains w/high tracking accuracy (>80 dB by V.C.A.) Noiseless, passive, high accuracy L/R balance 3-position switch for compressor /OFF/Limiter @ +10 dBu (= 6 VU, typically adjustable) Very high performance Compressor/Limiter, (THAT®'s V.C.A. loop) Threshold reference level, slope and R/C time constant internally adjustable External Power: 3.5 to 12 VDC Battery Power: 8 x "AA" batteries Size: 9.5" x 4.5" x 1.75" Weight: <5.0 lbs. with batteries
